SUNTEC MODEL “A” FUEL PUMP
The Model A Suntec Fuel Pump is designed for use on residential burners. These fuel units can be in all oil burners with a capacity of up to 3 GHP. Strainer Capacity (GHP) Nozzle Port Location Mounting 2721-605 Beckett-S 5LAY-05 313-28AB92 XD-BK204 … Access Content
ROUTINE · ANNUAL OR OTHER CHECK OUT
ROUTINE · ANNUAL OR OTHER CHECK OUT Check line filter and pump strainer for FUEL PUMP · TROUBLESHOOTING GUIDE Return unit to approved service station or Suntec factory for repair. If unit has been running dry, pour oil into pump prior to testing. … Content Retrieval
OIL PUMP TYPE E 1001 GEAR SIZES 4-6-7
E 1001 PUMP IDENTIFICATION (Not all model combinations are available Consult your Suntec representative) E : Pressure regulation Gear set capacity (see pump capacity curves) Strainer C : 170 µm N : 550 µm Shaft rotation and nozzle location (seen from shaft end) A : clockwise rotation/ right … Read Full Source
OIL PUMP TYPE J GEAR SIZES 4-6-7
Consult your Suntec representative) J : Pressure regulation Gear set capacity (see pump capacity curves) Strainer The SUNTEC J oil pump incorporates a pressure regulating valve with cut- … Return Doc
Oil pump (internal Combustion Engine) – Wikipedia, The Free …
The oil pump in an internal combustion engine circulates engine oil under pressure to the rotating oiling system, oil is drawn out of the oil sump (oil pan, in US English) through a wire mesh strainer that removes some of the larger pieces of debris from the oil. The flow made by the oil pump … Read Article
Oil pump
Range E wihout SOLENOID VAVE FOR MEDIUM FUEL OIL (1) Used for OERTLI E6CC and E7CC – (2) Strainer 170µm – (3) Strainer 550µm – (4) Type with flange – (5) Without in-line cut-off function – (6) Cover with hole for heating element The SUNTEC E oil pump incorporates a pressure regulating valve with … Read Here
Vacuum Gauge Port Oil Under Pressure Oil Under Suction By …
Consult your Suntec representative) E : Pressure regulation Gear set capacity (see pump capacity curves) Strainer The SUNTEC E 1001 oil pump incorporates a pressure regulating valve with … Get Content Here
USING THE PROPER GASKET FOR THE CLEANCUT PUMP
Suntec A2VA-7116 pump, however it operates in a significantly different way. gaskets are also acceptable with the A2VA-7116 pump. The top center hole in the gasket is required to allow oil to freely flow through the bypass (return) circuit. … View Document
OIL PUMP TYPE D GEAR SIZES 45-47-55-57-67
Covered herein, contact Suntec. The SUNTEC D oil pump is specially adapted for heavy oil (up to 200 cSt) Vacuum gauge port G 1/4" or G 1/8" Valve function Pressure regulating without cut-off Strainer Open area : 12 cm … Access Full Source
ALE OIL PUMP TYPE ALE GEAR SIZES 35-55
Contact Suntec. The SUNTEC ALE oil pump incorporates a blocking solenoid valve fitted with a built-in return Strainer open area : 6 cm2 – opening size : 150 µm Shaft Ø 8 mm according to EN 225 … Fetch Content
OIL PUMP TYPE AL GEAR SIZES 35-55-65-75-95
Covered herein, contact Suntec. The SUNTEC AL oil pump incorporates a blocking solenoid valve with in-line Strainer open area : 14 cm 2 (AL 35/55/65) – 20 cm 2 (AL 75/95). opening size : 150 µm. … Document Viewer
Webster Service Technician’s Handbook
**Pumping #2 oil (34SSUU). .85 Sp. gr. Supply Pump Unit Cross Reference Webster Model No. Suntec Model No. SPM-15-1 (1725 rpm) Be certain suction line filter or strainer has adequate capacity Rumble coming from burner at start-up Check cutoff at pump or external solenoid Oil leaking from pump … Access Document